MASSO Post Processor Help
Posted: Sun Apr 10, 2022 8:05 pm
I have been working on a post for a Masso Ver5 G3 controller with a DHTC and air Scribe.
I have almost everything setup the way I would like it, Basically there are 2 things I would like to change and I cant figure out how to do it.
First:
The PP I started with has the following code:
--The cutter will slow down for corners and turn off THC below this radius
slowRadius = 10
--Minimum slow down speed.
--This is a scale factor. For instance 0.5 = 50% of the current feed rate
slowPercent = 0.4
I would like to remove that & just use SC rules but I am not sure how to do it, any help would be appreciated!!
Second:
The G-Code output for scribing looks good, I don't see any issues but the Plasma operation G-Code output has one annoyance that I cant figure out, Here is an example of the output:
N0960 T112 M06
N0970 G92.1
N0980 G200 F20 P0.12 D400 C0.08 V92 A0 O0 S0
N0990 G00 X1.5857 Y3.7500
N1000 X2.6887 Y2.5756
N1010 M03 (---45 amp .090 aluminum---)
N1020 G01 F100.0 <----- Why is it doing this?
N1030 F120.0 <----- Why is it doing this?
N1040 G03 Y2.6887 I-0.0566 J0.0566 F48.0
N1050 M667 F50.0 (---THC on---)
N1060 X2.0000 Y2.9740 I-0.6887 J-0.6887 F120.0
N1070 X1.0260 Y2.0000 I0.0000 J-0.9740
N1080 X2.0000 Y1.0260 I0.9740 J-0.0000
N1090 X2.9740 Y2.0000 I0.0000 J0.9740
N1100 X2.6887 Y2.6887 I-0.9740 J0.0000
N1110 M666 (---THC off---)
I understand it doesn't really hurt anything but it is annoying & I would like to understand why its doing that..
Again any help here would be appreciated!!
Thanks!
Jeff
I have almost everything setup the way I would like it, Basically there are 2 things I would like to change and I cant figure out how to do it.
First:
The PP I started with has the following code:
--The cutter will slow down for corners and turn off THC below this radius
slowRadius = 10
--Minimum slow down speed.
--This is a scale factor. For instance 0.5 = 50% of the current feed rate
slowPercent = 0.4
I would like to remove that & just use SC rules but I am not sure how to do it, any help would be appreciated!!
Second:
The G-Code output for scribing looks good, I don't see any issues but the Plasma operation G-Code output has one annoyance that I cant figure out, Here is an example of the output:
N0960 T112 M06
N0970 G92.1
N0980 G200 F20 P0.12 D400 C0.08 V92 A0 O0 S0
N0990 G00 X1.5857 Y3.7500
N1000 X2.6887 Y2.5756
N1010 M03 (---45 amp .090 aluminum---)
N1020 G01 F100.0 <----- Why is it doing this?
N1030 F120.0 <----- Why is it doing this?
N1040 G03 Y2.6887 I-0.0566 J0.0566 F48.0
N1050 M667 F50.0 (---THC on---)
N1060 X2.0000 Y2.9740 I-0.6887 J-0.6887 F120.0
N1070 X1.0260 Y2.0000 I0.0000 J-0.9740
N1080 X2.0000 Y1.0260 I0.9740 J-0.0000
N1090 X2.9740 Y2.0000 I0.0000 J0.9740
N1100 X2.6887 Y2.6887 I-0.9740 J0.0000
N1110 M666 (---THC off---)
I understand it doesn't really hurt anything but it is annoying & I would like to understand why its doing that..
Again any help here would be appreciated!!
Thanks!
Jeff