Multiple shapes

Posts redirected from the Yahoo mailing list
Post Reply
Marius Liebenberg mari...

Multiple shapes

Post by Marius Liebenberg mari... »

Hi Les
The shapes plugin is a very exciting development and it has been long awaited. Well done mate.
A question please. I tried to do multiple shapes on one job or sheet. Is this possible as it seemed to replace the current shape with the new shape.


Regards


Marius
http://www.cnccontrol.co.za

http://www.mastercut.co.za





__._,_.___
Posted by: Marius Liebenberg <marius.liebenberg@yahoo.com>
Image

Visit Your Group
Unsubscribe ([email]sheetcam-unsubscribe@yahoogroups.com?subject=Unsubscribe[/email]) &bull; Terms of Use



__,_._,___
Marius Liebenberg mari...

Multiple shapes

Post by Marius Liebenberg mari... »

This is what I did.
I created a square and then duplicated it. Then I when back to shapes and crated a new shape. I used a pipe flange and then that replaced the square and its duplicate.
So I gather that you can have multiple shapes but all are grouped in a single part. Is this correct?




Regards


Marius
http://www.cnccontrol.co.za

http://www.mastercut.co.za





On Friday, December 26, 2014 12:40 PM, "Marius Liebenberg marius.liebenberg@yahoo.com [sheetcam]" <sheetcam@yahoogroups.com> wrote:




Hi Les
The shapes plugin is a very exciting development and it has been long awaited. Well done mate.
A question please. I tried to do multiple shapes on one job or sheet. Is this possible as it seemed to replace the current shape with the new shape.


Regards

Marius
http://www.cnccontrol.co.za
http://www.mastercut.co.za






#yiv0967383281 #yiv0967383281 -- #yiv0967383281ygrp-mkp { border:1px solid #d8d8d8;font-family:Arial;margin:10px 0;padding:0 10px;} #yiv0967383281 #yiv0967383281ygrp-mkp hr { border:1px solid #d8d8d8;} #yiv0967383281 #yiv0967383281ygrp-mkp #yiv0967383281hd { color:#628c2a;font-size:85%;font-weight:700;line-height:122%;margin:10px 0;} #yiv0967383281 #yiv0967383281ygrp-mkp #yiv0967383281ads { margin-bottom:10px;} #yiv0967383281 #yiv0967383281ygrp-mkp .yiv0967383281ad { padding:0 0;} #yiv0967383281 #yiv0967383281ygrp-mkp .yiv0967383281ad p { margin:0;} #yiv0967383281 #yiv0967383281ygrp-mkp .yiv0967383281ad a { color:#0000ff;text-decoration:none;} #yiv0967383281 #yiv0967383281ygrp-sponsor #yiv0967383281ygrp-lc { font-family:Arial;} #yiv0967383281 #yiv0967383281ygrp-sponsor #yiv0967383281ygrp-lc #yiv0967383281hd { margin:10px 0px;font-weight:700;font-size:78%;line-height:122%;} #yiv0967383281 #yiv0967383281ygrp-sponsor #yiv0967383281ygrp-lc .yiv0967383281ad { margin-bottom:10px;padding:0 0;} #yiv0967383281 #yiv0967383281actions { font-family:Verdana;font-size:11px;padding:10px 0;} #yiv0967383281 #yiv0967383281activity { background-color:#e0ecee;float:left;font-family:Verdana;font-size:10px;padding:10px;} #yiv0967383281 #yiv0967383281activity span { font-weight:700;} #yiv0967383281 #yiv0967383281activity span:first-child { text-transform:uppercase;} #yiv0967383281 #yiv0967383281activity span a { color:#5085b6;text-decoration:none;} #yiv0967383281 #yiv0967383281activity span span { color:#ff7900;} #yiv0967383281 #yiv0967383281activity span .yiv0967383281underline { text-decoration:underline;} #yiv0967383281 .yiv0967383281attach { clear:both;display:table;font-family:Arial;font-size:12px;padding:10px 0;width:400px;} #yiv0967383281 .yiv0967383281attach div a { text-decoration:none;} #yiv0967383281 .yiv0967383281attach img { border:none;padding-right:5px;} #yiv0967383281 .yiv0967383281attach label { display:block;margin-bottom:5px;} #yiv0967383281 .yiv0967383281attach label a { text-decoration:none;} #yiv0967383281 blockquote { margin:0 0 0 4px;} #yiv0967383281 .yiv0967383281bold { font-family:Arial;font-size:13px;font-weight:700;} #yiv0967383281 .yiv0967383281bold a { text-decoration:none;} #yiv0967383281 dd.yiv0967383281last p a { font-family:Verdana;font-weight:700;} #yiv0967383281 dd.yiv0967383281last p span { margin-right:10px;font-family:Verdana;font-weight:700;} #yiv0967383281 dd.yiv0967383281last p span.yiv0967383281yshortcuts { margin-right:0;} #yiv0967383281 div.yiv0967383281attach-table div div a { text-decoration:none;} #yiv0967383281 div.yiv0967383281attach-table { width:400px;} #yiv0967383281 div.yiv0967383281file-title a, #yiv0967383281 div.yiv0967383281file-title a:active, #yiv0967383281 div.yiv0967383281file-title a:hover, #yiv0967383281 div.yiv0967383281file-title a:visited { text-decoration:none;} #yiv0967383281 div.yiv0967383281photo-title a, #yiv0967383281 div.yiv0967383281photo-title a:active, #yiv0967383281 div.yiv0967383281photo-title a:hover, #yiv0967383281 div.yiv0967383281photo-title a:visited { text-decoration:none;} #yiv0967383281 div#yiv0967383281ygrp-mlmsg #yiv0967383281ygrp-msg p a span.yiv0967383281yshortcuts { font-family:Verdana;font-size:10px;font-weight:normal;} #yiv0967383281 .yiv0967383281green { color:#628c2a;} #yiv0967383281 .yiv0967383281MsoNormal { margin:0 0 0 0;} #yiv0967383281 o { font-size:0;} #yiv0967383281 #yiv0967383281photos div { float:left;width:72px;} #yiv0967383281 #yiv0967383281photos div div { border:1px solid #666666;height:62px;overflow:hidden;width:62px;} #yiv0967383281 #yiv0967383281photos div label { color:#666666;font-size:10px;overflow:hidden;text-align:center;white-space:nowrap;width:64px;} #yiv0967383281 #yiv0967383281reco-category { font-size:77%;} #yiv0967383281 #yiv0967383281reco-desc { font-size:77%;} #yiv0967383281 .yiv0967383281replbq { margin:4px;} #yiv0967383281 #yiv0967383281ygrp-actbar div a:first-child { margin-right:2px;padding-right:5px;} #yiv0967383281 #yiv0967383281ygrp-mlmsg { font-size:13px;font-family:Arial, helvetica, clean, sans-serif;} #yiv0967383281 #yiv0967383281ygrp-mlmsg table { font-size:inherit;font:100%;} #yiv0967383281 #yiv0967383281ygrp-mlmsg select, #yiv0967383281 input, #yiv0967383281 textarea { font:99% Arial, Helvetica, clean, sans-serif;} #yiv0967383281 #yiv0967383281ygrp-mlmsg pre, #yiv0967383281 code { font:115% monospace;} #yiv0967383281 #yiv0967383281ygrp-mlmsg * { line-height:1.22em;} #yiv0967383281 #yiv0967383281ygrp-mlmsg #yiv0967383281logo { padding-bottom:10px;} #yiv0967383281 #yiv0967383281ygrp-msg p a { font-family:Verdana;} #yiv0967383281 #yiv0967383281ygrp-msg p#yiv0967383281attach-count span { color:#1E66AE;font-weight:700;} #yiv0967383281 #yiv0967383281ygrp-reco #yiv0967383281reco-head { color:#ff7900;font-weight:700;} #yiv0967383281 #yiv0967383281ygrp-reco { margin-bottom:20px;padding:0px;} #yiv0967383281 #yiv0967383281ygrp-sponsor #yiv0967383281ov li a { font-size:130%;text-decoration:none;} #yiv0967383281 #yiv0967383281ygrp-sponsor #yiv0967383281ov li { font-size:77%;list-style-type:square;padding:6px 0;} #yiv0967383281 #yiv0967383281ygrp-sponsor #yiv0967383281ov ul { margin:0;padding:0 0 0 8px;} #yiv0967383281 #yiv0967383281ygrp-text { font-family:Georgia;} #yiv0967383281 #yiv0967383281ygrp-text p { margin:0 0 1em 0;} #yiv0967383281 #yiv0967383281ygrp-text tt { font-size:120%;} #yiv0967383281 #yiv0967383281ygrp-vital ul li:last-child { border-right:none !important; } #yiv0967383281









__._,_.___
Posted by: Marius Liebenberg <marius.liebenberg@yahoo.com>
Image

Visit Your Group
Unsubscribe ([email]sheetcam-unsubscribe@yahoogroups.com?subject=Unsubscribe[/email]) &bull; Terms of Use



__,_._,___
PK
Posts: 362
Joined: Thu May 10, 2012 9:58 am

Post by PK »

Les,

Multiple shapes work just fine here.

Paul
Attachments
shapes.png
shapes.png (3.21 KiB) Viewed 3092 times
Les Newell les.newell@...

Multiple shapes

Post by Les Newell les.newell@... »

Hi Marius,

As Tony mentioned you need to use 'new shape' to create multiple shapes. If you duplicate a part you are just creating a step-and-repeat of the original part so any changes to the original will be reflected in all of the duplicates. If you copy the part you create an independent copy that is not affected by any changes in the original.

Les

On 26/12/14 10:59, Marius Liebenberg marius.liebenberg@yahoo.com (marius.liebenberg@yahoo.com) [sheetcam] wrote:
This is what I did.
I created a square and then duplicated it. Then I when back to shapes and crated a new shape. I used a pipe flange and then that replaced the square and its duplicate.
So I gather that you can have multiple shapes but all are grouped in a single part. Is this correct?


 
Regards


Marius
http://www.cnccontrol.co.za

http://www.mastercut.co.za






__._,_.___
Posted by: Les Newell <les.newell@fastmail.co.uk>
Image

Visit Your Group
Unsubscribe ([email]sheetcam-unsubscribe@yahoogroups.com?subject=Unsubscribe[/email]) &bull; Terms of Use



__,_._,___
Vmax549
Posts: 641
Joined: Mon Nov 09, 2009 5:55 pm

Post by Vmax549 »

HIYA LES, You may want to consider a SNAP TO Part function so you can create several shapes then overlay them on each other and have them SNAP TO say the center point if needed. Otherwiase it would HARD to get them aligned exactly as needed.

Just a thought, (;-) TP
Vmax549
Posts: 641
Joined: Mon Nov 09, 2009 5:55 pm

Post by Vmax549 »

You may also want to add a conversation command line input Where you program individual segments of the part.

Line , StartPoint, Endpoint

Arc , StartPoint, End Point, I,J OR Radius of the arc.

Circle, CenterPoint, Radius or Diameter

Drill , CenterPoint , Depth, Return, FeedRate


This makes it VERY easy to create a part from a Blueprint or drawing or just out of your head.

It is VERY usefull here for simple things.

Just a thought, (;-) TP
Scott V
Posts: 25
Joined: Fri May 12, 2006 6:37 am

Post by Scott V »

I like it... :D

Les,
thanks for all your good work!
Attachments
sheetcam 16 ga 20 amp tips.jpg
sheetcam 16 ga 20 amp tips.jpg (221.49 KiB) Viewed 3016 times
sheetcam 16 ga 20 amp tips.jpg
sheetcam 16 ga 20 amp tips.jpg (221.49 KiB) Viewed 3016 times
Post Reply