6.9.10 Graphics area not displaying after update
-
- Posts: 452
- Joined: Wed Sep 12, 2018 8:18 pm
- Location: South Carolina, USA
- Contact:
6.9.10 Graphics area not displaying after update
Les, major issue after update this morning. 6.9.10 isnt showing the graphics area and says unable to display. Tried restarting, clicking every botton, nothing will display.
- Les Newell
- Site Admin
- Posts: 3665
- Joined: Thu May 11, 2006 8:12 pm
Re: 6.9.10 Graphics area not displaying after update
I spotted this shortly after it went up. A new release should be up by now. Sorry about that
-
- Posts: 452
- Joined: Wed Sep 12, 2018 8:18 pm
- Location: South Carolina, USA
- Contact:
Re: 6.9.10 Graphics area not displaying after update
Okay awesome! Interestingly, the table display still doesnt show until i toggle the table display icon...
- Les Newell
- Site Admin
- Posts: 3665
- Joined: Thu May 11, 2006 8:12 pm
Re: 6.9.10 Graphics area not displaying after update
Sigh. I'm not doing well today. A new update is on it's way.
By the way, the noSafeZ warning now won't show a message box. Could you check the log to see if it appears there. It will be in the first few lines if it's there.
By the way, the noSafeZ warning now won't show a message box. Could you check the log to see if it appears there. It will be in the first few lines if it's there.
-
- Posts: 452
- Joined: Wed Sep 12, 2018 8:18 pm
- Location: South Carolina, USA
- Contact:
Re: 6.9.10 Graphics area not displaying after update
I know the feeling man, my day is about the same lol.
The noSafeZ did appear in one log file so far, so it appears to be less consistent but still exists.
I also noticed two other periodic errors:
1) Error: OpenGL error: invalid value
2) Assert failure in function wxCSConv::wxCSConv (C:\wx-3.0\wxWidgets\src\common\strconv.cpp:2873). invalid encoding value in wxCSConv ctor ("Assert failure")
The first appears fairly consistent and the second has only appeared once so far, immediately after the update.
The noSafeZ did appear in one log file so far, so it appears to be less consistent but still exists.
I also noticed two other periodic errors:
1) Error: OpenGL error: invalid value
2) Assert failure in function wxCSConv::wxCSConv (C:\wx-3.0\wxWidgets\src\common\strconv.cpp:2873). invalid encoding value in wxCSConv ctor ("Assert failure")
The first appears fairly consistent and the second has only appeared once so far, immediately after the update.
- Les Newell
- Site Admin
- Posts: 3665
- Joined: Thu May 11, 2006 8:12 pm
Re: 6.9.10 Graphics area not displaying after update
Thanks for those logs.
I had hoped my changes would fix the noSafeZ issue. As far as I can tell something is writing to incorrect memory addresses and stomping on the settings. If this is the case it is pretty serious as it could trash other settings. The problem is that it is extremely difficult to figure out what is doing it.
The OpenGl error is minor and should be fixed in the next release. That wxCSConv error is a new one. It is not one that concerns me all that much.
I had hoped my changes would fix the noSafeZ issue. As far as I can tell something is writing to incorrect memory addresses and stomping on the settings. If this is the case it is pretty serious as it could trash other settings. The problem is that it is extremely difficult to figure out what is doing it.
The OpenGl error is minor and should be fixed in the next release. That wxCSConv error is a new one. It is not one that concerns me all that much.
-
- Posts: 452
- Joined: Wed Sep 12, 2018 8:18 pm
- Location: South Carolina, USA
- Contact:
Re: 6.9.10 Graphics area not displaying after update
No problem.
I did have an error with the post processor before lunch with the 6.9.11 update, but while i was at lunch before i had a chance to see what it was, you released 6.9.12 and it fixed it. An error popped up after that update saying the saved post cold not be found, but i reloaded the machine profile and all APEARS to be fine now.
I did have an error with the post processor before lunch with the 6.9.11 update, but while i was at lunch before i had a chance to see what it was, you released 6.9.12 and it fixed it. An error popped up after that update saying the saved post cold not be found, but i reloaded the machine profile and all APEARS to be fine now.