Floating Z axis problem

Having problems with or questions about SheetCam? Post them here.
Itchy Kiwis
Posts: 11
Joined: Fri May 08, 2020 12:50 am
Location: Australia

Floating Z axis problem

Post by Itchy Kiwis »

I’m new to this plasma cutting magic and I’ve hit a problem I can’t get my head around
My z axis doesn’t seem to be zeroing it’s self at touch off
I’ve set my 6.6mm so switch offset in post processor
For MACH3 I’ve got a vid showing what’s going on here
https://youtu.be/8ouE7YKrcpo
Any ideas ?
User avatar
djreiswig
Posts: 471
Joined: Sat Feb 20, 2016 4:47 am
Location: SE Nebraska

Re: Floating Z axis problem

Post by djreiswig »

The switch offset should be the distance from when the switch clicks moving down to when the switch clicks moving up. Exactly. Jog your z down slowly until the switch clicks and zero the z then jog the z up slowly until the switch clicks. The offset should be what the z dro reads.
It looks like your z is adding extra distance every time it references. Does the z dro show zero when the switch is closed going down and then zero again after it retracts?
User avatar
Les Newell
Site Admin
Posts: 3661
Joined: Thu May 11, 2006 8:12 pm

Re: Floating Z axis problem

Post by Les Newell »

It looks like you are getting a different height every time. I have come across some Mach odditities when probing on older versions of Mach. What version of Mach are you using?
What post processor are you using?
Itchy Kiwis
Posts: 11
Joined: Fri May 08, 2020 12:50 am
Location: Australia

Re: Floating Z axis problem

Post by Itchy Kiwis »

Hi guys and thank you for your input
I have set switch offset as 6.6mm not sure if it should be a neg or pos number
post processor is Mach3 plasma with scriber and backlash compensation. the only edited part was the switch offset as mentioned earlier
here is the link to the test file out put from sheet cam
https://filebin.net/pluyfbazn3l84c9q/te ... t=9q90luov
mach3 version is version R3.043.066
User avatar
Les Newell
Site Admin
Posts: 3661
Joined: Thu May 11, 2006 8:12 pm

Re: Floating Z axis problem

Post by Les Newell »

Try the 'Mach3 thc with scriber' post.
Itchy Kiwis
Posts: 11
Joined: Fri May 08, 2020 12:50 am
Location: Australia

Re: Floating Z axis problem

Post by Itchy Kiwis »

ok I used mach3 thc with scriber and got a strange result in mach3
https://www.dropbox.com/s/idwgtjhlssfu2 ... .jpeg?dl=0
it sends my cutter in circles all over the place
I have run the simulator in sheet cam and found everything ok
but also I have noticed that the torch turns off too soon as well you might have noticed this in the previous video
and isn't sheet cam supposed to trigger mach3?
this is an image of my file in sheet cam https://www.dropbox.com/s/gwxhkt6afld9g ... .jpeg?dl=0
User avatar
Les Newell
Site Admin
Posts: 3661
Joined: Thu May 11, 2006 8:12 pm

Re: Floating Z axis problem

Post by Les Newell »

In Mach go to Config->general config In the second column set the 'IJ mode' to Inc. If it is set to Absolute you will get these symptoms.
Itchy Kiwis
Posts: 11
Joined: Fri May 08, 2020 12:50 am
Location: Australia

Re: Floating Z axis problem

Post by Itchy Kiwis »

Thank you Les I’ll try that today 👍🏼
Itchy Kiwis
Posts: 11
Joined: Fri May 08, 2020 12:50 am
Location: Australia

Re: Floating Z axis problem

Post by Itchy Kiwis »

sorry bout delay in reply my control board had issues
and victim of cyber hacking
Les I contacted you earlier by email but no reply
is there a chance of you resending my licence?
User avatar
Les Newell
Site Admin
Posts: 3661
Joined: Thu May 11, 2006 8:12 pm

Re: Floating Z axis problem

Post by Les Newell »

I can't find your email. I'll get a copy of your license sent to you.
Itchy Kiwis
Posts: 11
Joined: Fri May 08, 2020 12:50 am
Location: Australia

Re: Floating Z axis problem

Post by Itchy Kiwis »

Received thanks les great !
Now it’s back to the plasma cutting end of things
Itchy Kiwis
Posts: 11
Joined: Fri May 08, 2020 12:50 am
Location: Australia

Re: Floating Z axis problem

Post by Itchy Kiwis »

Ok using MACH3 with scriber post and still no touch off to zero and continuously rising z axis
I know the probe function is working and calibrated Z
Here’s a vid https://youtu.be/vQPCtXhEcKY
User avatar
djreiswig
Posts: 471
Joined: Sat Feb 20, 2016 4:47 am
Location: SE Nebraska

Re: Floating Z axis problem

Post by djreiswig »

Is your probe input lighting up before the z starts going back up? It seems like you must be getting a phantom input in order for it to reverse.
User avatar
Les Newell
Site Admin
Posts: 3661
Joined: Thu May 11, 2006 8:12 pm

Re: Floating Z axis problem

Post by Les Newell »

Yes it definitely looks like the touch-off is tripping far too early. Are you sure the touch-off switch is wired correctly? In Mach3's diagnostics watch the probe input while you run that job.
Itchy Kiwis
Posts: 11
Joined: Fri May 08, 2020 12:50 am
Location: Australia

Re: Floating Z axis problem

Post by Itchy Kiwis »

Yes the probe is functioning as it should I swapped over to NC active high and I created a simple little 40mm Square and ran it
All ran just as badly as before
Except this time I recorded the diagnostic screen and ran from there
https://youtu.be/fdxNyqwz9aU
Post Reply