Hi.
I'm very often getting annoying error messages like:
"Some paths were not generated correctly. There could be a problem with
the drawing."
Is there a way to figure out why Sheetcam reports this? Checking the
drawing manually can be rather time consuming ant typically I don't find
anything.
Best regards, Torleif.
------------------------------------
Yahoo Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/sheetcam/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/sheetcam/join
(Yahoo! ID required)
<*> To change settings via email:
sheetcam-digest@yahoogroups.com
sheetcam-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
sheetcam-unsubscribe@yahoogroups.com
<*> Your use of Yahoo Groups is subject to:
https://info.yahoo.com/legal/us/yahoo/utos/terms/
Annoying drawing error messages - how to debug?
Annoying drawing error messages - how to debug?
Hi Torleif,
That normally indicates that something has gone wrong with the path
generation. It happens when you offset a closed contour but the end
result is an open path. This should not happen. In most cases if the cut
paths look good it will cut fine.
Les
On 06/05/2014 19:57, Torleif Jensen wrote:
------------------------------------
Yahoo Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/sheetcam/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/sheetcam/join
(Yahoo! ID required)
<*> To change settings via email:
sheetcam-digest@yahoogroups.com
sheetcam-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
sheetcam-unsubscribe@yahoogroups.com
<*> Your use of Yahoo Groups is subject to:
https://info.yahoo.com/legal/us/yahoo/utos/terms/
That normally indicates that something has gone wrong with the path
generation. It happens when you offset a closed contour but the end
result is an open path. This should not happen. In most cases if the cut
paths look good it will cut fine.
Les
On 06/05/2014 19:57, Torleif Jensen wrote:
Hi.
I'm very often getting annoying error messages like:
"Some paths were not generated correctly. There could be a problem with
the drawing."
Is there a way to figure out why Sheetcam reports this? Checking the
drawing manually can be rather time consuming ant typically I don't find
anything.
Best regards, Torleif.
------------------------------------
Yahoo Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/sheetcam/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/sheetcam/join
(Yahoo! ID required)
<*> To change settings via email:
sheetcam-digest@yahoogroups.com
sheetcam-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
sheetcam-unsubscribe@yahoogroups.com
<*> Your use of Yahoo Groups is subject to:
https://info.yahoo.com/legal/us/yahoo/utos/terms/
Annoying drawing error messages - how to debug?
I have trouble with hidden open paths too. Sometimes it is a tiny detail in a large nest and it can be difficult to track down. Is their a way to highlight the source of the open path?
-------- Original message --------
From: Les Newell <les.newell@fastmail.co.uk>
Date:
To: sheetcam@yahoogroups.com
Subject: Re: [sheetcam] Annoying drawing error messages - how to debug?
Hi Torleif,
That normally indicates that something has gone wrong with the path
generation. It happens when you offset a closed contour but the end
result is an open path. This should not happen. In most cases if the cut
paths look good it will cut fine.
Les
On 06/05/2014 19:57, Torleif Jensen wrote:
------------------------------------
Yahoo Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/sheetcam/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/sheetcam/join
(Yahoo! ID required)
<*> To change settings via email:
sheetcam-digest@yahoogroups.com
sheetcam-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
sheetcam-unsubscribe@yahoogroups.com
<*> Your use of Yahoo Groups is subject to:
https://info.yahoo.com/legal/us/yahoo/utos/terms/
__._,_.___
Visit Your Group
Unsubscribe ([email]sheetcam-unsubscribe@yahoogroups.com?subject=Unsubscribe[/email]) • Terms of Use
__,_._,___
-------- Original message --------
From: Les Newell <les.newell@fastmail.co.uk>
Date:
To: sheetcam@yahoogroups.com
Subject: Re: [sheetcam] Annoying drawing error messages - how to debug?
Hi Torleif,
That normally indicates that something has gone wrong with the path
generation. It happens when you offset a closed contour but the end
result is an open path. This should not happen. In most cases if the cut
paths look good it will cut fine.
Les
On 06/05/2014 19:57, Torleif Jensen wrote:
Hi.
I'm very often getting annoying error messages like:
"Some paths were not generated correctly. There could be a problem with
the drawing."
Is there a way to figure out why Sheetcam reports this? Checking the
drawing manually can be rather time consuming ant typically I don't find
anything.
Best regards, Torleif.
------------------------------------
Yahoo Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/sheetcam/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/sheetcam/join
(Yahoo! ID required)
<*> To change settings via email:
sheetcam-digest@yahoogroups.com
sheetcam-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
sheetcam-unsubscribe@yahoogroups.com
<*> Your use of Yahoo Groups is subject to:
https://info.yahoo.com/legal/us/yahoo/utos/terms/
__._,_.___
Visit Your Group
Unsubscribe ([email]sheetcam-unsubscribe@yahoogroups.com?subject=Unsubscribe[/email]) • Terms of Use
__,_._,___
Annoying drawing error messages - how to debug?
Are you getting the same warning or are tehse just ordinary open paths? You can show open paths by selecting View->show path ends. All open paths will have white dots at each end.
Les
On 08/05/2014 00:54, dtimes1 wrote:
__._,_.___
Visit Your Group
Unsubscribe ([email]sheetcam-unsubscribe@yahoogroups.com?subject=Unsubscribe[/email]) • Terms of Use
__,_._,___
Les
On 08/05/2014 00:54, dtimes1 wrote:
I have trouble with hidden open paths too. Sometimes it is a tiny detail in a large nest and it can be difficult to track down. Is their a way to highlight the source of the open path?
__._,_.___
Visit Your Group
Unsubscribe ([email]sheetcam-unsubscribe@yahoogroups.com?subject=Unsubscribe[/email]) • Terms of Use
__,_._,___
Annoying drawing error messages - how to debug?
Ordinary open paths I'd say. I will give your suggestion a go.
-------- Original message --------
From: "Les Newell les.newell@fastmail.co.uk [sheetcam]" <sheetcam@yahoogroups.com>
Date:
To: sheetcam@yahoogroups.com
Subject: Re: [sheetcam] Annoying drawing error messages - how to debug?
Are you getting the same warning or are tehse just ordinary open paths? You can show open paths by selecting View->show path ends. All open paths will have white dots at each end.
Les
On 08/05/2014 00:54, dtimes1 wrote:
__._,_.___
Visit Your Group
Unsubscribe ([email]sheetcam-unsubscribe@yahoogroups.com?subject=Unsubscribe[/email]) • Terms of Use
__,_._,___
-------- Original message --------
From: "Les Newell les.newell@fastmail.co.uk [sheetcam]" <sheetcam@yahoogroups.com>
Date:
To: sheetcam@yahoogroups.com
Subject: Re: [sheetcam] Annoying drawing error messages - how to debug?
Are you getting the same warning or are tehse just ordinary open paths? You can show open paths by selecting View->show path ends. All open paths will have white dots at each end.
Les
On 08/05/2014 00:54, dtimes1 wrote:
I have trouble with hidden open paths too. Sometimes it is a tiny detail in a large nest and it can be difficult to track down. Is their a way to highlight the source of the open path?
__._,_.___
Visit Your Group
Unsubscribe ([email]sheetcam-unsubscribe@yahoogroups.com?subject=Unsubscribe[/email]) • Terms of Use
__,_._,___