[Tool0]
Type=PlasmaTool
Name=P-PT40ASM-16gaHR
Name_Edited=1
Comment=Tecmo Original \nTECMO PTM60 torch from PrimeWeld\nmodified nozzle tip, removed outside shoulder at tip, made conical like HT45 nozzle tip\nmuch better performane, no dross collection at nozzle-shield gap\n\n35amps, 65psi, 84thcv\n@750mm/m plunge speed, ramp traverse takes 0.25s with 2.2mm PH-CH transition\nfeed 1400mm/m, gives great cut, minor dross bottom\nkerf 1.1mm\nPD 0.7\nno leadin open shapes ok with these settings.
Tool\ number=2
Kerf\ width=1.1
Path\ rules=LdcPlasmaRules
Plunge\ rate=750
Pierce\ delay=0.7
Pause\ at\ end\ of\ cut=0.8
Wiggle\ length=10
Pierce\ height=3.7
Cut\ height=1.5
Pierce\ type=1
Feed\ rate=1400
Lead\ in=4
Lead\ out=2
Lead\ in\ type=1
Lead\ out\ type=1
CodeSnip=-1
Hole\ Size=20
Use\ leadin\ settings=1
[Tool1]
Type=PlasmaTool
Name=P-PT40ASM-14gaHR
Name_Edited=1
Comment=Tecmo Original \nTECMO PTM60 torch from PrimeWeld\nmodified nozzle tip, removed outside shoulder at tip, made conical like HT45 nozzle tip\nmuch better performane, no dross collection at nozzle-shield gap\n\n35amps, 65psi, 85thcv\n@750mm/m plunge speed, ramp traverse takes 0.25s with 2.2mm PH-CH transition\nfeed 1250mm/m, gives great cut, minor dross bottom\nkerf 1.1mm\nPD 0.8\nno leadin open shapes ok with these settings.
Tool\ number=3
Kerf\ width=1.1
Path\ rules=LdcPlasmaRules
Plunge\ rate=750
Pierce\ delay=0.8
Pause\ at\ end\ of\ cut=0.8
Wiggle\ length=10
Pierce\ height=3.7
Cut\ height=1.5
Pierce\ type=1
Feed\ rate=1250
Lead\ in=4
Lead\ out=2
Lead\ in\ type=1
Lead\ out\ type=1
CodeSnip=-1
Hole\ Size=20
Use\ leadin\ settings=1
[Tool2]
Type=MarkerTool
Name=EasyScriber
Name_Edited=1
Comment=https://theeasyscriber.com/userguide.html
Tool\ number=10
Diameter=0.2
Path\ rules=
Plunge\ rate=1000
Start\ delay=0.1
Pause\ at\ end\ of\ cut=0.1
Wiggle\ length=10
Pierce\ height=3
Cut\ height=-2
Pierce\ type=0
Feed\ rate=2540
Lead\ in=6
Lead\ out=3
Lead\ in\ type=1
Lead\ out\ type=1
CodeSnip=-1
Hole\ Size=20
Use\ leadin\ settings=0
[Tool3]
Type=MillTool
Name=M-3.175 mm SF
Name_Edited=1
Comment=
Tool\ number=20
Diameter=3.175
Path\ rules=
Flute\ length=12.699999999999999
Spindle\ speed=18000
Spindle\ direction=0
Tool\ length\ offset=0
Depth\ per\ pass=1.5
Point\ angle=2.059488517353309
Plunge\ rate=500
Feed\ rate=1463
Ramp\ Angle=0
[Tool4]
Type=MillTool
Name=M-6.35 mm SF
Name_Edited=1
Comment=
Tool\ number=21
Diameter=6.35
Path\ rules=
Flute\ length=21.59
Spindle\ speed=18000
Spindle\ direction=0
Tool\ length\ offset=0
Depth\ per\ pass=2
Point\ angle=2.059488517353309
Plunge\ rate=500
Feed\ rate=2540
Ramp\ Angle=0
[Tool5]
Type=MillTool
Name=M-6.35 mm LF
Name_Edited=1
Comment=
Tool\ number=22
Diameter=6.299
Path\ rules=
Flute\ length=38.100000000000001
Spindle\ speed=18000
Spindle\ direction=0
Tool\ length\ offset=0
Depth\ per\ pass=2
Point\ angle=2.059488517353309
Plunge\ rate=500
Feed\ rate=2103
Ramp\ Angle=0
[Tool6]
Type=VTool
Name=M-V60 deg
Name_Edited=1
Comment=verify specs before use
Tool\ number=27
Tip\ diameter=0.2
Path\ rules=
Flute\ length=11.113
Spindle\ speed=18000
Spindle\ direction=0
Tool\ length\ offset=0
Depth\ per\ pass=2
V\ angle=1.047197551196598
Plunge\ rate=500
Feed\ rate=1016
Ramp\ Angle=0
[Tool7]
Type=VTool
Name=M-V90 deg
Name_Edited=1
Comment=
Tool\ number=28
Tip\ diameter=1
Path\ rules=
Flute\ length=4.775
Spindle\ speed=18000
Spindle\ direction=0
Tool\ length\ offset=0
Depth\ per\ pass=1.5
V\ angle=1.570796326794897
Plunge\ rate=500
Feed\ rate=1016
Ramp\ Angle=0
[Tool8]
Type=MillTool
Name=M-28.575 mm fly
Name_Edited=1
Comment=
Tool\ number=29
Diameter=28.574999999999999
Path\ rules=
Flute\ length=12.699999999999999
Spindle\ speed=18000
Spindle\ direction=0
Tool\ length\ offset=0
Depth\ per\ pass=1
Point\ angle=2.059488517353309
Plunge\ rate=500
Feed\ rate=2540
Ramp\ Angle=0.785398163397448
[Tool9]
Type=PlasmaTool
Name=P-HT30A-16gaHR
Name_Edited=1
Comment=HT PMX 30XP  / RazorWeld 45 style consumables\nTECMO UPM-105 torch from PrimeWeld\nPlasmaDyn PMX 30XP 51204 nozzle\n28set/30cut amps, 72 psi\nTHC parms: 2.0 dly, 100 spd, 175 HV\nthcv 77\nmaterial tested on 2/5/24
Tool\ number=31
Kerf\ width=0.9
Path\ rules=LdcPlasmaRules
Plunge\ rate=551
Pierce\ delay=0.4
Pause\ at\ end\ of\ cut=0.3
Wiggle\ length=10
Pierce\ height=3.7
Cut\ height=1.5
Pierce\ type=0
Feed\ rate=1700
Lead\ in=2
Lead\ out=2
Lead\ in\ type=1
Lead\ out\ type=0
CodeSnip=-1
Hole\ Size=19.5
Use\ leadin\ settings=1
[Tool10]
Type=PlasmaTool
Name=P-HT45AS-16gaHR
Name_Edited=1
Comment=HT PMX 45 style / RazorWeld 45 consumables\nTECMO UPM-105 torch from PrimeWeld\n40set/45cut amps, 72 psi, 85 thcv \nFR adjusted to 2400 and thcv 85 based on 14ga. testing. **verify on next use**\n\nTHC parms: 2.0 dly, 100 spd, 175 HV\n1/28/24- leadin, leadout, endDelay, plunge
Tool\ number=41
Kerf\ width=1
Path\ rules=LdcPlasmaRules
Plunge\ rate=450
Pierce\ delay=0.5
Pause\ at\ end\ of\ cut=0.3
Wiggle\ length=10
Pierce\ height=3.7
Cut\ height=1.5
Pierce\ type=0
Feed\ rate=2400
Lead\ in=2
Lead\ out=2
Lead\ in\ type=1
Lead\ out\ type=0
CodeSnip=-1
Hole\ Size=19.5
Use\ leadin\ settings=1
[Tool11]
Type=PlasmaTool
Name=P-HT45AS-14gaHR
Name_Edited=1
Comment=HT PMX 45 style / RazorWeld 45 consumables\nTECMO UPM-105 torch from PrimeWeld\n40set/45cut amps, 72 psi, \nPD 0.6s good using scpost v23.2\nTHC parms: 2.0 dly, 100 spd, 175 HV\nUpdates: \n10/24/23- KEMAO nzl&shld-- THC dly, spd, HV, thcv 89\n1/27-28/24- PW nzl&shld-- leadin, leadout, plunge, endDelay, kerf, thcv 84 \ntry reducing PD to 0.55 to improve (reduce) open shape pierce hole
Tool\ number=42
Kerf\ width=1.25
Path\ rules=LdcPlasmaRules
Plunge\ rate=450
Pierce\ delay=0.55
Pause\ at\ end\ of\ cut=0.3
Wiggle\ length=10
Pierce\ height=3.7
Cut\ height=1.5
Pierce\ type=0
Feed\ rate=2200
Lead\ in=3
Lead\ out=2
Lead\ in\ type=1
Lead\ out\ type=0
CodeSnip=-1
Hole\ Size=19.5
Use\ leadin\ settings=1
[Tool12]
Type=PlasmaTool
Name=P-HT45AS-12gaHR
Name_Edited=1
Comment=HT PMX 45 style / RazorWeld 45 consumables\nTECMO UPM-105 torch from PrimeWeld\n40set/45cut amps, 72 psi, 85 thcv w KEMAO nzl&shld\nTHC parms: 2.0 dly, 100 spd, 175 HV\nUpdates: \n2/3/2024- PW nzl&shld-- copied from 14ga tool, guess adjustments\ninterestingly I guessed 1800mm/m, but mistakenly used 2200mm/m and it worked great.
Tool\ number=43
Kerf\ width=1.25
Path\ rules=LdcPlasmaRules
Plunge\ rate=450
Pierce\ delay=0.6
Pause\ at\ end\ of\ cut=0.3
Wiggle\ length=10
Pierce\ height=3.7
Cut\ height=1.5
Pierce\ type=0
Feed\ rate=2200
Lead\ in=4
Lead\ out=2
Lead\ in\ type=1
Lead\ out\ type=0
CodeSnip=-1
Hole\ Size=19.5
Use\ leadin\ settings=1
[Tool13]
Type=PlasmaTool
Name=P-HT45AS-11gaHR
Name_Edited=1
Comment=HyperTherm Powermax 45 / RazorWeld 45 consumables\nTECMO UPM-105 torch from PrimeWeld\n45 amps, 75 psi, 92 thcv nominal\nrevisit PD and FR when next used, 16ga tool reduced 0.2s on 9/2/23
Tool\ number=44
Kerf\ width=1.3
Path\ rules=LdcPlasmaRules
Plunge\ rate=450
Pierce\ delay=0.9
Pause\ at\ end\ of\ cut=0.8
Wiggle\ length=10
Pierce\ height=3.7
Cut\ height=1.5
Pierce\ type=1
Feed\ rate=1000
Lead\ in=6
Lead\ out=2
Lead\ in\ type=1
Lead\ out\ type=1
CodeSnip=-1
Hole\ Size=20
Use\ leadin\ settings=1
[Tool14]
Type=PlasmaTool
Name=P-HT45AS-12gaSS
Name_Edited=1
Comment=HyperTherm Powermax 45 / RazorWeld 45 consumables\nTECMO UPM-105 torch from PrimeWeld\n45 amps, 72 psi, 87 thcv nominal\n\nphillips66 job on 10/26/23\nPD adjusted after job to 0.9s from 1.0\nthcv adj to 87 from 92\nTHC Dly 2.0, SPD 100, HV 175\n\nat 1600mm/m there is a lot of top side sparks but top and bottom dross looks good.\nconsider 10% slower FR next time
Tool\ number=45
Kerf\ width=1.3
Path\ rules=LdcPlasmaRules
Plunge\ rate=450
Pierce\ delay=0.9
Pause\ at\ end\ of\ cut=0.8
Wiggle\ length=10
Pierce\ height=3.7
Cut\ height=1.5
Pierce\ type=1
Feed\ rate=1600
Lead\ in=4
Lead\ out=1
Lead\ in\ type=1
Lead\ out\ type=1
CodeSnip=-1
Hole\ Size=13
Use\ leadin\ settings=1
[Tool15]
Type=PlasmaTool
Name=P-HT45AS-0.25inHR
Name_Edited=1
Comment=HyperTherm Powermax 45 / RazorWeld 45 consumables\nTECMO UPM-105 torch from PrimeWeld\n45 amps, 75 psi, 95 thcv nominal\nrevisit PD and FR  when next used, 16ga tool reduced 0.2s on 9/2/23
Tool\ number=46
Kerf\ width=1.5
Path\ rules=LdcPlasmaRules
Plunge\ rate=350
Pierce\ delay=1.1
Pause\ at\ end\ of\ cut=0.8
Wiggle\ length=10
Pierce\ height=3.7
Cut\ height=1.5
Pierce\ type=1
Feed\ rate=500
Lead\ in=6
Lead\ out=2
Lead\ in\ type=1
Lead\ out\ type=1
CodeSnip=-1
Hole\ Size=20
Use\ leadin\ settings=1
[Tool16]
Type=CodeTool
Name=Disable THC
Name_Edited=1
Comment=
Tool\ number=2147483647
Code=G91 G1 X0 S0 (block THC Z ctrl w ADC w continuous motion) \nG90
[Tool17]
Type=CodeTool
Name=Enable THC
Name_Edited=1
Comment=
Tool\ number=268435456
Code=G91 G1 X0 S1000  (enable THC Z ctrl w ADC w continuous motion) \nG90
[pathRules]
GlobalRule=-1
[pathRules/Set0]
name=LdcPlasmaRules
[pathRules/Set0/Rule0]
Class=PathRuleOnStart
Feed\ rate=1
Start\ code=-1
End\ code=268435456
Enabled=1
Distance=75
[pathRules/Set0/Rule1]
Class=PathRuleOnCircle
Feed\ rate=0.9
Start\ code=2147483647
End\ code=-1
Enabled=1
Smaller\ than=18
[pathRules/Set0/Rule2]
Class=PathRuleOnCircle
Feed\ rate=0.85
Start\ code=2147483647
End\ code=-1
Enabled=1
Smaller\ than=13
[pathRules/Set0/Rule3]
Class=PathRuleOnCircle
Feed\ rate=0.8
Start\ code=2147483647
End\ code=-1
Enabled=1
Smaller\ than=8
[pathRules/Set0/Rule4]
Class=PathRuleBeforeEnd
Feed\ rate=1
Start\ code=2147483647
End\ code=-1
Enabled=1
Distance=2
Include\ leadout=1