Search found 3656 matches
- Thu Oct 22, 2015 1:13 pm
- Forum: Problems and questions
- Topic: .hpgl 3D
- Replies: 4
- Views: 2431
- Thu Oct 22, 2015 12:15 pm
- Forum: Problems and questions
- Topic: .hpgl 3D
- Replies: 4
- Views: 2431
- Sat Oct 17, 2015 10:24 am
- Forum: Problems and questions
- Topic: Can Sheetcam do this with X, Y and Z?
- Replies: 3
- Views: 1764
- Thu Oct 15, 2015 7:27 pm
- Forum: Problems and questions
- Topic: Error in post processor
- Replies: 2
- Views: 1625
- Thu Oct 15, 2015 2:27 pm
- Forum: Problems and questions
- Topic: Bad characters!
- Replies: 2
- Views: 1697
Does it look correct in Mach? If so you are losing position somehow. What drives are you using? I have experienced lost steps with Gecko drives if they are pushed too hard. Try reducing your acceleration and see if it makes any difference. Another possibility is electrical noise. Be very careful wit...
- Wed Oct 14, 2015 4:21 pm
- Forum: Problems and questions
- Topic: Scanything - PC power needs ??
- Replies: 2
- Views: 2095
- Sun Oct 04, 2015 9:49 am
- Forum: Problems and questions
- Topic: Problems with plate marker
- Replies: 5
- Views: 2963
- Wed Sep 30, 2015 9:05 am
- Forum: Problems and questions
- Topic: edited postprocesors don't work
- Replies: 2
- Views: 3955
The posts supplied with SheetCam are stored in Program Files along with SheetCam. Due to file permissions on later versions of Windows it is not possible for normal users to edit any files in Program Files. To get around this when you edit a post in SheetCam it copies the post to application data (i...
- Mon Sep 28, 2015 12:46 pm
- Forum: Problems and questions
- Topic: Post prossessor or FT-1
- Replies: 2
- Views: 1342
- Sat Sep 26, 2015 6:27 pm
- Forum: Problems and questions
- Topic: Post error??
- Replies: 8
- Views: 3426
- Sat Sep 26, 2015 9:13 am
- Forum: Problems and questions
- Topic: Post error??
- Replies: 8
- Views: 3426
That post was written by Tom at CandCNC so I'm not all that familiar with how it works but I think the seventh line in your sample should be commented out. Again I'm not sure exactly why Tom turns off THC after the pierce. His system is quite sophisticated and there is probably a very good reason wh...
- Thu Sep 24, 2015 6:17 pm
- Forum: Problems and questions
- Topic: Material save & load misses one value?
- Replies: 5
- Views: 2424
- Thu Sep 24, 2015 6:16 pm
- Forum: Problems and questions
- Topic: Modifying the Job Report Summary
- Replies: 5
- Views: 3368
- Wed Sep 23, 2015 4:22 pm
- Forum: Problems and questions
- Topic: Windows 10 and Sheetcam TNG 6.0.15
- Replies: 2
- Views: 4404
The last time I saw that error it turned out to be a display driver bug. It is quite likely you have a similar problem. The tricky bit will be finding alternate display drivers for your machine that will work with Win 10. I have seen a number of issues with Win10 and to be honest I would recommend t...
- Wed Sep 23, 2015 4:12 pm
- Forum: Problems and questions
- Topic: Post error??
- Replies: 8
- Views: 3426