Search found 484 matches
- Thu Dec 15, 2022 6:01 pm
- Forum: Problems and questions
- Topic: Apply Operation to All Parts
- Replies: 7
- Views: 24847
Re: Apply Operation to All Parts
I'm wondering how copy all operations would differ from apply to all parts. Would think the part specific specs would just not be applied in either case.
- Thu Dec 15, 2022 3:18 pm
- Forum: Problems and questions
- Topic: Apply Operation to All Parts
- Replies: 7
- Views: 24847
Re: Apply Operation to All Parts
But you can copy/paste an operation from one part to another.
- Sun Dec 04, 2022 2:03 am
- Forum: Problems and questions
- Topic: Select & move multiple parts on material
- Replies: 5
- Views: 16025
Re: Select & move multiple parts on material
Worked great. Thanks.
- Sat Dec 03, 2022 2:25 am
- Forum: Problems and questions
- Topic: Can I set Lua variables using cut rules?
- Replies: 4
- Views: 793
Re: Can I set Lua variables using cut rules?
I'm guessing the snippets are always going to be on a new line. Maybe Les will chime in. I don't use snippets.
- Fri Dec 02, 2022 6:53 pm
- Forum: New features
- Topic: Lead in and lead out with line cutting and tab holding.
- Replies: 15
- Views: 7458
Re: Lead in and lead out with line cutting and tab holding.
Nice job. That eliminates the dimple from an extra pierce.
- Thu Dec 01, 2022 4:48 am
- Forum: Problems and questions
- Topic: Add overcut in tools??
- Replies: 2
- Views: 673
Re: Add overcut in tools??
I don't think this is something you can do in the post. I think the overcut is an internal function inside SheetCam. Possibly it could be changed to a tool setting like the leads were a while back.
- Wed Nov 30, 2022 3:07 pm
- Forum: Problems and questions
- Topic: Select & move multiple parts on material
- Replies: 5
- Views: 16025
Select & move multiple parts on material
Is there a way to select multiple parts in a job and move them together? Specifically, I have a standard nest on a 4x8 sheet. Sometimes the sheet is slightly smaller or larger. I cut from the corner opposite of 0,0, so I can easily rezero when I reuse the material later. The problem is, if the sheet...
- Tue Nov 29, 2022 12:59 pm
- Forum: New features
- Topic: Lead in and lead out with line cutting and tab holding.
- Replies: 15
- Views: 7458
Re: Lead in and lead out with line cutting and tab holding.
You may also have problems with wrecking your consumables from the blowback when it's not cutting through.
- Mon Nov 28, 2022 2:51 am
- Forum: Problems and questions
- Topic: Can I set Lua variables using cut rules?
- Replies: 4
- Views: 793
Re: Can I set Lua variables using cut rules?
You should be able to set up the THC totally inside the post. That's how my candcnc setup works. How do you determine where the code snippets go currently? That might help figure out how the post needs modified. Also, which post are you using?
- Fri Nov 11, 2022 9:59 pm
- Forum: Problems and questions
- Topic: Issues with recent update
- Replies: 9
- Views: 1514
Re: Issues with recent update
In this specific case I have to disagree. You have not yet saved a job under that name and you may want to call it something else. It also gets complicated if you have loaded and nested multiple drawings. You may want to save the job as something other than a drawing name. Les, I agree with you on ...
- Thu Nov 10, 2022 6:28 pm
- Forum: Problems and questions
- Topic: Issues with recent update
- Replies: 9
- Views: 1514
Re: Issues with recent update
I second the odd saving behavior. I've brought it up before. Any other program have used, when closing a file that has previously been saved with a valid filename and then modified will not bring up a save as dialog. It just saves. Only times the save as dialog comes up is if selected off of the fil...
- Mon Nov 07, 2022 6:10 pm
- Forum: Problems and questions
- Topic: Toolset question
- Replies: 3
- Views: 1040
Re: Toolset question
You can save and load toolsets. Should be in the file menu. I think there can only be one default toolset, but you should be able to have as many other toolsets as you want.
- Tue Nov 01, 2022 9:53 pm
- Forum: Problems and questions
- Topic: uncontrolled z
- Replies: 1
- Views: 408
Re: uncontrolled z
What does the M31 macro do? The code looks like it should only raise to 0.1880". I'm guessing the M31 is a touchoff macro. Is it possibly doing something with the z coordinates? Can you single step through the code to see where the problem might be?
- Tue Nov 01, 2022 12:16 am
- Forum: Problems and questions
- Topic: Open contour negative overcut
- Replies: 6
- Views: 1367
Re: Open contour negative overcut
I don't think I would ever use overcut on open paths, but maybe a checkbox option like lead in on open paths. This should eliminate the established functionality issue. As a side note, I'm not sure where using a lead in on an open path would be useful. I'm wondering why a lead in, but not a lead out...
- Sat Oct 15, 2022 11:42 pm
- Forum: New features
- Topic: Cutting holes on rotary
- Replies: 6
- Views: 3431
Re: Cutting holes on rotary
Why not just cut the holes using the rotary axis?