Search found 79 matches
- Sun Apr 29, 2018 11:20 pm
- Forum: Problems and questions
- Topic: stops at layer changes
- Replies: 28
- Views: 9160
Re: stops at layer changes
Thankyou jim1108. After doing some 'educating' utube style, that code that you have written is in 'absolute' mode. This will first raise the Z to 100mm at the rapid speed, then move the 'X' and the 'Y' to the 0 0 position also at the rapid speed then pause. Now again a stupid question. Is it just th...
- Sun Apr 29, 2018 3:52 am
- Forum: Problems and questions
- Topic: stops at layer changes
- Replies: 28
- Views: 9160
Re: stops at layer changes
Good morning jim108. Got the job done yesterday afternoon, with out the tool change code snipet put in, but had to baby sit the machine and some stuffing around, but nevertheless it got done, so am happy with that. Reading the sheetcam book got the code snipet in the correct place to put in the cutt...
- Tue Apr 24, 2018 11:38 pm
- Forum: Problems and questions
- Topic: stops at layer changes
- Replies: 28
- Views: 9160
Re: stops at layer changes
Good morning jim1108. Was out all yesterday on site playing with a pilot boat and was knackered after that. Again thankyou for that I will give this a go and see what happens. Today after some breakdown completions will be routing out the first sheet of HDPE, however this one doesn't need any tool c...
- Mon Apr 23, 2018 10:12 am
- Forum: Problems and questions
- Topic: stops at layer changes
- Replies: 28
- Views: 9160
Re: stops at layer changes
Good morning jim1108. Yest that is what I am trying to achieve. Want the machine to stop, again at a convenient place for the tool change, do the tool change and then continue :mrgreen: . Zeroing out the tool I can just do manually so not worried about that, but what you have here is perfect. Just a...
- Sun Apr 22, 2018 3:41 am
- Forum: Problems and questions
- Topic: stops at layer changes
- Replies: 28
- Views: 9160
Re: stops at layer changes
Thankyou for that jim.
Now what I need to know is how and where to put in this code snipet
Now what I need to know is how and where to put in this code snipet
- Sat Apr 21, 2018 9:21 am
- Forum: Problems and questions
- Topic: stops at layer changes
- Replies: 28
- Views: 9160
stops at layer changes
As the hedding may suggest, what i am after is, when in sheetcam you setup a layer, once that layer is completed will Mach3 stop and require the start button to be pressed. I will word it differently, I have not taken as much notice as probably I should have. What I am trying to achive is this. I wi...
- Sat Apr 21, 2018 9:21 am
- Forum: Problems and questions
- Topic: stops at layer changes
- Replies: 0
- Views: 6261
stops at layer changes
As the hedding may suggest, what i am after is, when in sheetcam you setup a layer, once that layer is completed will Mach3 stop and require the start button to be pressed. I will word it differently, I have not taken as much notice as probably I should have. What I am trying to achive is this. I wi...
- Sun Feb 25, 2018 9:32 am
- Forum: Problems and questions
- Topic: editing drawing in sheetcam
- Replies: 3
- Views: 1341
Re: editing drawing in sheetcam
Good morning les. Dirty method works for me, I will try this and see how it goes. Once this is done it's there for always, which what I wanted. Thanks again
- Fri Feb 23, 2018 10:29 pm
- Forum: Problems and questions
- Topic: editing drawing in sheetcam
- Replies: 3
- Views: 1341
editing drawing in sheetcam
Good morning all. Just a question had a dxf file sent to me and the hole sizes are 20mm but need to be 22mm. Is there a way to change this in sheetcam. Need to get this out today if possible and not wait till Monday. Any help would be greatly appreciated.
- Fri Jul 22, 2016 12:28 pm
- Forum: Problems and questions
- Topic: Riik words
- Replies: 6
- Views: 2651
- Tue Jul 19, 2016 12:19 am
- Forum: Problems and questions
- Topic: Riik words
- Replies: 6
- Views: 2651
- Sun Jul 17, 2016 10:32 am
- Forum: Problems and questions
- Topic: Riik words
- Replies: 6
- Views: 2651
Riik words
Good morning Les. Was wondering if you have ever come accros this before. Late last week I went to cut some material. Did all the post processing in sheetcam, did a simulation and all was OK. When I ran the G code in Mach3 it came up with 'error Riik words all missing from arc. Block=NO420 Z57.150. ...
- Tue Mar 01, 2016 9:23 pm
- Forum: Problems and questions
- Topic: VAT for purchases into Australia
- Replies: 2
- Views: 1750
- Tue Mar 01, 2016 1:57 am
- Forum: Problems and questions
- Topic: VAT for purchases into Australia
- Replies: 2
- Views: 1750
VAT for purchases into Australia
Good morning Les
I would like to get scananything and the rotary plugin, however it comes up with the VAT code. If you are selling outside the EU dose this still apply.
Would like to get these items underway. My licence code is VJLSL9P6, arranges through Tom candcnc.
I would like to get scananything and the rotary plugin, however it comes up with the VAT code. If you are selling outside the EU dose this still apply.
Would like to get these items underway. My licence code is VJLSL9P6, arranges through Tom candcnc.
- Fri Sep 18, 2015 11:47 pm
- Forum: New features
- Topic: Plate marking
- Replies: 4
- Views: 6958