Search found 161 matches
- Sat Apr 24, 2021 9:20 am
- Forum: Problems and questions
- Topic: Says report bug and cutter wobbles at end of part
- Replies: 8
- Views: 1331
Re: Says report bug and cutter wobbles at end of part
Whenever I get the message about the paths not being generated correctly, it's normally a bad file I imported. Things like crossed lines, loops in the line, or even tiny separate lines/shapes. Most of the time they are extremely small and you have to really zoom in to find them, but they are there. ...
- Mon Apr 19, 2021 10:09 pm
- Forum: Problems and questions
- Topic: Plasma THC preset voltage
- Replies: 7
- Views: 2378
Re: Plasma THC preset voltage
How does the THC know what so set as nominal voltage if it's not specified in the G-code? Depends on the type of THC. Many THCs are completely external to the controller (Mach3, etc) and thus the voltage is set on the THC itself. Some THCs are built into the controller and you can set on the screen...
- Mon Apr 19, 2021 10:00 pm
- Forum: Problems and questions
- Topic: Plasma THC preset voltage
- Replies: 7
- Views: 2378
- Thu Jan 21, 2021 1:48 pm
- Forum: Problems and questions
- Topic: Post processor "entityClosed" always returning zero
- Replies: 2
- Views: 854
Re: Post processor "entityClosed" always returning zero
Ah I see.
Thanks for that Les. Good job I didn't keep trying, wouldn't have got very far
Thanks for that Les. Good job I didn't keep trying, wouldn't have got very far
- Thu Jan 21, 2021 10:37 am
- Forum: Problems and questions
- Topic: Post processor "entityClosed" always returning zero
- Replies: 2
- Views: 854
Post processor "entityClosed" always returning zero
Hi Les, I've been at this several hours trying to figure out what I'm doing wrong. Could you give me some guidance on how to use the Sheetcam variable "entityClosed". I believe this is supposed to test whether the next path is open or closed. Variable is 1 if path is closed and 0 if path i...
- Wed Jan 20, 2021 9:22 pm
- Forum: Problems and questions
- Topic: How to add M1 after each part
- Replies: 4
- Views: 1587
Re: How to add M1 after each part
Thanks Les,
that's definitely going to help.
that's definitely going to help.
- Wed Jan 20, 2021 11:05 am
- Forum: Problems and questions
- Topic: How to add M1 after each part
- Replies: 4
- Views: 1587
Re: How to add M1 after each part
Thanks Wyogreen, that would do for just a few parts but was looking for something a little more "automated" if for example I brought in a single nested "part" then used "Break Up Manually Nested Drawing" to make each shape a separate part in Sheetcam. I'll look into the...
- Tue Jan 19, 2021 11:01 pm
- Forum: Problems and questions
- Topic: How to add M1 after each part
- Replies: 4
- Views: 1587
How to add M1 after each part
Hi Les, when plasma cutting parts with tip up risk, it can be useful to put M1 at the end of SafeZ after a cut. The gcode stops and if all is well the operator simply presses Cycle Start and the cut continues. Or if the part tipped up, pick it out, then press Cycle Start. I can easily insert M1 in t...
- Sun Dec 20, 2020 11:25 pm
- Forum: Problems and questions
- Topic: Torch not stopping before end of cut
- Replies: 8
- Views: 1938
Re: Torch not stopping before end of cut
Cheers Rob,
armed with that new knowledge that I need the Mesa cards too, I might just hold off for a while. Had a lot of outgoings lately. Can't do much experimenting with a black screen
Might check out the simulator though.
Keith
armed with that new knowledge that I need the Mesa cards too, I might just hold off for a while. Had a lot of outgoings lately. Can't do much experimenting with a black screen
Might check out the simulator though.
Keith
- Sat Dec 19, 2020 10:29 pm
- Forum: Problems and questions
- Topic: Torch not stopping before end of cut
- Replies: 8
- Views: 1938
Re: Torch not stopping before end of cut
I hope I'm wrong.... I really genuinely do.... I see you got replies.... proof of the pudding is in the eating.... see what they release.... (wonder how soon though... just watch and wait) I'm back dabbling with linuxcnc (path pilot) for a lathe .... see what happens. for my needs (plasma) uccnc do...
- Wed Dec 16, 2020 10:00 pm
- Forum: Problems and questions
- Topic: Torch not stopping before end of cut
- Replies: 8
- Views: 1938
Re: Torch not stopping before end of cut
Thanks for the reply Rob. I'm starting to wonder if you are right. This thread: https://www.forum.cncdrive.com/viewtopic.php?f=3&t=2083 which I started one and a half years ago to get a very simply software fix done to the UCR201 hand pendant plugin, has not had a solution so far. Just had words...
- Wed Dec 16, 2020 11:00 am
- Forum: Problems and questions
- Topic: Torch not stopping before end of cut
- Replies: 8
- Views: 1938
Re: Torch not stopping before end of cut
uccnc has proved good..... but with covid they have been slow (non existent) with development since Feb 2020 Rob, is it fair to say they have been non existent with development. Have you heard from a reliable source that they have done zero development from February. Dezsoe claims UCCNC is still un...
- Fri Dec 04, 2020 10:54 pm
- Forum: Problems and questions
- Topic: What bugs you the most in SheetCam?
- Replies: 156
- Views: 10662464
Re: What bugs you the most in SheetCam?
"Break Up Manually Nested Drawing" changes the cut order. I prefer to nest parts in Coreldraw instead of in Sheetcam, so I'll export the nested parts from CD as a single file, and import into Sheetcam as a single part. I create any needed layers and operations, place start positions and cr...
- Sat Oct 31, 2020 9:18 pm
- Forum: Problems and questions
- Topic: Academic question on calculating arc length.
- Replies: 7
- Views: 1734
Re: Academic question on calculating arc length.
curiosity has got me Keith, what are you experimenting with? Hi Rob, you know the THC that I designed. It's another feature I'd like to add to that. If you got a flameout during a cut, the system would either automatically or upon a button press (depending on setting), reverse along the cut path a ...
- Fri Oct 30, 2020 1:35 pm
- Forum: Problems and questions
- Topic: Academic question on calculating arc length.
- Replies: 7
- Views: 1734
Re: Academic question on calculating arc length.
Thanks a bunch Les. That was really hurting my head for a few minutes until something clicked when you said, "If you are using degrees........" So then I thought is Les using those Radian thingies (you see the mathematician in me :lol: ). So I check out Google and find there are pi radians...