Search found 474 matches

by djreiswig
Fri Nov 10, 2023 3:15 pm
Forum: Problems and questions
Topic: Masso tube plasma post
Replies: 15
Views: 14900

Re: Masso tube plasma post

I've toyed around with the rotary post a bit, but haven't actually run any of the code yet. I do believe that SheetCam runs the rotary axis in linear units rather than degrees. It uses the center axis as z zero.
I think you also have to purchase the rotary plugin for any of the rotary stuff to work.
by djreiswig
Thu Nov 09, 2023 12:06 pm
Forum: Problems and questions
Topic: plasma THC define custom tool parameter for THC set volts
Replies: 9
Views: 40467

Re: plasma THC define custom tool parameter for THC set volts

Which section did you insert the define in? I believe it has to be in a certain place. Look at another post that has a custom parameter and see where it goes.
by djreiswig
Wed Nov 08, 2023 3:13 pm
Forum: Problems and questions
Topic: Perforated sheet metal
Replies: 3
Views: 2468

Re: Perforated sheet metal

That must be something that your controller uses. It's not a normal SheetCam setting. If you look through the gcode, it's probably being sent to the controller.
by djreiswig
Tue Nov 07, 2023 3:41 pm
Forum: Problems and questions
Topic: Perforated sheet metal
Replies: 3
Views: 2468

Re: Perforated sheet metal

Does the 45xp have a mode for cutting perforated sheet? My 65 has a setting on the dial that keeps the arc running even if it goes off of the metal momentarily.
by djreiswig
Sat Nov 04, 2023 7:43 pm
Forum: Problems and questions
Topic: Error Code
Replies: 2
Views: 2126

Re: Error Code

There is a limit on the number of lines of gcode that the evaluation version will output. To fix this error you'll have to purchase SheetCam. If you are getting this error on a licensed copy, then it's possible that your license code is pirated. If this is the case, contact Les at SheetCam with your...
by djreiswig
Tue Oct 31, 2023 1:18 am
Forum: Problems and questions
Topic: Masso tube plasma post
Replies: 15
Views: 14900

Re: Masso tube plasma post

The PMs stay in your outbox until the receiver reads them.
by djreiswig
Mon Oct 30, 2023 9:08 pm
Forum: Problems and questions
Topic: Plasma peck drilling function issue
Replies: 6
Views: 3814

Re: Plasma peck drilling function issue

What post processor is the person who sent you the other image using? I think CandCNC is the one that has the peck pierce programmed into their post. You would probably have to add those functions to your post to get that to work.
by djreiswig
Mon Oct 30, 2023 8:15 pm
Forum: Problems and questions
Topic: Plasma peck drilling function issue
Replies: 6
Views: 3814

Re: Plasma peck drilling function issue

That's probably a different post processor. Tell us more about your system.
by djreiswig
Mon Oct 30, 2023 7:17 pm
Forum: Problems and questions
Topic: Plasma peck drilling function issue
Replies: 6
Views: 3814

Re: Plasma peck drilling function issue

On some plasma cutters the initial pierce is longer. After the post flow air is running, the pierce time is shorter. Try dry firing the torch before you start your code to get the air flowing and see if that works better.
by djreiswig
Fri Oct 27, 2023 7:05 pm
Forum: Problems and questions
Topic: Adding Options to Plasma Tool dialog - not enigh screen space
Replies: 6
Views: 5919

Re: Adding Options to Plasma Tool dialog - not enigh screen space

Can you make the lower section of the window display in 2 columns if there are too many fields to fit? I would think that would be easier than scrolling and would make better use of the window.
by djreiswig
Tue Oct 17, 2023 4:26 pm
Forum: Problems and questions
Topic: All pierces first?
Replies: 3
Views: 2524

Re: All pierces first?

There is a plugin that makes toolbar buttons that will let you easily run more that one post. I believe it's called moreposts. You could also add a setting to your post that would allow a switch of sorts in the operation that would toggle the pierces only. I think it would be easier to have 2 differ...
by djreiswig
Tue Oct 17, 2023 3:46 am
Forum: Problems and questions
Topic: All pierces first?
Replies: 3
Views: 2524

Re: All pierces first?

You will have to copy & edit your post processor to only perform the rapids & pierces and ignore the cut moves. What post are you using?
by djreiswig
Mon Sep 25, 2023 1:22 pm
Forum: Problems and questions
Topic: Rotary drawing issue
Replies: 7
Views: 3042

Re: Rotary drawing issue

It's in the operations screen. There's a checkbox.
by djreiswig
Tue Sep 19, 2023 10:57 am
Forum: Problems and questions
Topic: Where are predefined variables set?
Replies: 5
Views: 3613

Re: Where are predefined variables set?

On a rotary axis the Z is calculated from the center of the pipe not the surface.
by djreiswig
Sun Sep 17, 2023 6:05 pm
Forum: Problems and questions
Topic: Rotary drawing issue
Replies: 7
Views: 3042

Re: Rotary drawing issue

Split the hole on its own layer. Then you can inside offset the hole and outside offset the other lines. You might have to play with the start points to get the offset on the correct side. Also, make sure you select offset open paths.