Thanks, and so true putting the mouse to work, I read Les's reply above for a second time, makes sense now
thanks all
Search found 9 matches
- Thu Jul 30, 2020 5:31 pm
- Forum: Problems and questions
- Topic: Operations feedrate verses tool feedrate
- Replies: 7
- Views: 1127
- Wed Jul 29, 2020 7:58 pm
- Forum: Problems and questions
- Topic: Operations feedrate verses tool feedrate
- Replies: 7
- Views: 1127
Re: Operations feedrate verses tool feedrate
Thanks, thats what I needed to know Being new to plasma art work, is there a time that an operation for one cut would be faster/slower in different cut. If so, wouldn't it make sense the tool populates the speed in operation and you can change if you needed in operation to over ride the tool setting...
- Tue Jul 28, 2020 8:43 pm
- Forum: Problems and questions
- Topic: Operations feedrate verses tool feedrate
- Replies: 7
- Views: 1127
Operations feedrate verses tool feedrate
Lets say the feedrate in the tool is set for 100-ipm and when you set up an operation its 75-ipm, does one take priority over another.
I read another post where they were saying slow the feedrate on the operation of a hole, so was wondering if operation over rides the tool setup
thx
les
I read another post where they were saying slow the feedrate on the operation of a hole, so was wondering if operation over rides the tool setup
thx
les
- Tue Jul 07, 2020 7:17 pm
- Forum: Problems and questions
- Topic: Vector Curve No end Points get processor error cutting
- Replies: 8
- Views: 1259
Re: Vector Curve No end Points get processor error cutting
Thanks Les. Al is working fine now and the full cut is clean now when I run simulation in NC Viewer. I am confident it will work now
- Mon Jul 06, 2020 4:13 pm
- Forum: Problems and questions
- Topic: Vector Curve No end Points get processor error cutting
- Replies: 8
- Views: 1259
Re: Vector Curve No end Points get processor error cutting
screen shots of sheetcam
- Mon Jul 06, 2020 4:12 pm
- Forum: Problems and questions
- Topic: Vector Curve No end Points get processor error cutting
- Replies: 8
- Views: 1259
Re: Vector Curve No end Points get processor error cutting
attachments of job
- Mon Jul 06, 2020 4:10 pm
- Forum: Problems and questions
- Topic: Vector Curve No end Points get processor error cutting
- Replies: 8
- Views: 1259
Re: Vector Curve No end Points get processor error cutting
Hi Les So I created a single line/curve with 2 segments, when I apply operation/plasma/tool and say ok, it closes the curve, this is before I even run the post processor. I have attached the sheetcam file and several screen shots as well as post processor output In sheetcam, it shows a lot of segmen...
- Mon Jul 06, 2020 1:36 am
- Forum: Problems and questions
- Topic: Vector Curve No end Points get processor error cutting
- Replies: 8
- Views: 1259
sheetcam BUG Re: Vector Curve No end Points get processor error cutting
I tried to ass the # of segments all the way to 50, and did not work, now I am getting a line that closes the segment to cut see attached, this has to be a sheetcam bug
- Sat Jul 04, 2020 11:17 pm
- Forum: Problems and questions
- Topic: Vector Curve No end Points get processor error cutting
- Replies: 8
- Views: 1259
Vector Curve No end Points get processor error cutting
Hello I am working with a plasma cutter. I have a file of a car with single lines and lines that have curves with segments in it. When I run the post processor, everything is great. I take it to the plasma cutter and I get a load error. Complaining that a line has no end points. This used to work in...