Thanks, Les.
I'll give those a try.
Search found 16 matches
- Wed Mar 23, 2016 7:12 pm
- Forum: Problems and questions
- Topic: Path Pilot Post?
- Replies: 2
- Views: 1640
- Wed Mar 23, 2016 10:50 am
- Forum: Problems and questions
- Topic: Path Pilot Post?
- Replies: 2
- Views: 1640
Path Pilot Post?
Is there a Post Processor file for TNG and Path Pilot?
- Sat Jan 16, 2016 10:40 am
- Forum: New features
- Topic: Sequential mouse click ordering of Start Points
- Replies: 5
- Views: 6073
- Tue Apr 21, 2015 2:44 pm
- Forum: Yahoo posts
- Topic:
- Replies: 0
- Views: 7626
I usually just draw the exact pockets I want to cut regardless of the part. I draw the stock size. Then overlay hole placement and pockets. Sometimes multiple pockets. It works pretty well that way. Lee Styron Leeway Workshop, LLC On 4/21/2015 9:09 AM, Brian Lamb blamb11@cox.net ( blamb11@cox.net ) ...
- Wed Nov 27, 2013 10:27 pm
- Forum: New features
- Topic: manual nesting
- Replies: 2
- Views: 4198
manual nesting
I do a lot of manual nesting for my plasma cutter and often use different size sheets. I do all nesting in my Cad program and use the sheet size as a border. I find it is very easy to do that way. I may not get as close as A high dollar nesting program might, but it would take a bunch of the small p...
- Mon Dec 17, 2012 2:07 pm
- Forum: Problems and questions
- Topic: Using SC on a router and a plasma cutter?
- Replies: 2
- Views: 2041
- Sat Dec 15, 2012 2:55 pm
- Forum: Problems and questions
- Topic: Using SC on a router and a plasma cutter?
- Replies: 2
- Views: 2041
Using SC on a router and a plasma cutter?
I would like to use SC that I have been using for both a mill and a router on a plasma cutter now. Are there different profiles for Sheetcam? In other words, the way I used it on the mill and router were similar. Will setting up SC for a plasma lose the setting for the mill? I always use an old job ...
- Sun Jan 29, 2012 3:29 pm
- Forum: Problems and questions
- Topic: Can't force a start point where I want it.
- Replies: 4
- Views: 3407
- Sun Jan 29, 2012 3:16 pm
- Forum: Problems and questions
- Topic: Can't force a start point where I want it.
- Replies: 4
- Views: 3407
- Sun Jan 29, 2012 9:51 am
- Forum: Problems and questions
- Topic: Can't force a start point where I want it.
- Replies: 4
- Views: 3407
Never mind
Must have been a regen issue.
Seems to work fine now.
I'll make note if it happens again, but with the first few tries after rebooting TNG, all is golden.
Seems to work fine now.
I'll make note if it happens again, but with the first few tries after rebooting TNG, all is golden.
- Sun Jan 29, 2012 12:03 am
- Forum: Problems and questions
- Topic: Can't force a start point where I want it.
- Replies: 4
- Views: 3407
Can't force a start point where I want it.
I have some slots that I am milling. These are right on the edge of a profile, but they are their own geometry on their own layer as well. These are not open lines, but closed paths. Inside offset. Like a pocket, but a milling op. I want the start point on the outside of the profile, so the end mill...
- Mon Aug 08, 2011 8:21 am
- Forum: Problems and questions
- Topic: Trouble with TNG not posting
- Replies: 2
- Views: 2027
My license did show. I didn't get any error messages. While it didn't work correctly in either win 7 64 bit alone or in comp. mode, I did install Virtual PC and used XP Mode. Then installed TNG there and now it's good times once again. :) Works like it should. I thought that was kinda odd in the fir...
- Sun Aug 07, 2011 9:06 pm
- Forum: Problems and questions
- Topic: Trouble with TNG not posting
- Replies: 2
- Views: 2027
Trouble with TNG not posting
I recently had to upgrade my computer after a lightning strike.
Went with W7 64.
I still have a good backup of all the files I used including my PP. I just can't get TNG to post more than 6 or 7 lines of code.
I am running it in compatibility mode for XP SP3.
Any ideas?
Thanks.
Lee
Went with W7 64.
I still have a good backup of all the files I used including my PP. I just can't get TNG to post more than 6 or 7 lines of code.
I am running it in compatibility mode for XP SP3.
Any ideas?
Thanks.
Lee
- Sun Mar 09, 2008 5:17 am
- Forum: Problems and questions
- Topic: No Posts?
- Replies: 0
- Views: 2803
No Posts?
Hi Les. I reverted back to XP from Vista for awhile. I uploaded Sheetcam to this HD for the first time using the newest release. It didn't load any post processor choices. It's just blank. I can fix it, but just curious about it. Ver. 5.1.11 Thanks. ------------------------ Lee -------------------- ...
- Tue Feb 19, 2008 4:09 pm
- Forum: Problems and questions
- Topic: No Posts?
- Replies: 0
- Views: 3216
No Posts?
Hi Les.
I reverted back to XP from Vista for awhile. I uploaded Sheetcam to this HD for the first time using the newest release. It didn't load any post processor choices. It's just blank.
I can fix it, but just curious about it. Ver. 5.1.11
Thanks.
I reverted back to XP from Vista for awhile. I uploaded Sheetcam to this HD for the first time using the newest release. It didn't load any post processor choices. It's just blank.
I can fix it, but just curious about it. Ver. 5.1.11
Thanks.