Search found 11 matches

by pdevloo
Mon Apr 13, 2020 2:59 am
Forum: Problems and questions
Topic: Sheetcam and Openbuilds Control
Replies: 15
Views: 2367

Re: Sheetcam and Openbuilds Control

Disregard the last post, figured it out, problem was with Openbuilds GRBL settings, the Laser Mode was enabled which is in place to fire a laser immediately with table motion as far as I understand, that relates to the safety of it, anyway, disabled it and table works perfectly as it should, thanks ...
by pdevloo
Sun Apr 12, 2020 7:10 pm
Forum: Problems and questions
Topic: Sheetcam and Openbuilds Control
Replies: 15
Views: 2367

Re: Sheetcam and Openbuilds Control

Ive figured out I had to set sheet cam to ms instead of seconds and it delayed the torch, problem is, it also delayed the table. Its now doing the same thing where is starts cutting and motors travelling at same time but now has delay before it does it. Is there a way I could get the torch to fire b...
by pdevloo
Wed Feb 05, 2020 3:22 am
Forum: Problems and questions
Topic: Sheetcam and Openbuilds Control
Replies: 15
Views: 2367

Re: Sheetcam and Openbuilds Control

I set it to 0 sec, then set it to 4 seconds, made no difference, its only moving while the torch is firing on tabs, the start up works fine
by pdevloo
Mon Feb 03, 2020 5:03 am
Forum: Problems and questions
Topic: Sheetcam and Openbuilds Control
Replies: 15
Views: 2367

Re: Sheetcam and Openbuilds Control

I want to give my torch some time to fire before the motors start moving the machine, I'm not familiar with changing my post processor, checked out the Openbuilds forum, they recommend something like G1F1\nM3S1000\nG4 P400 code added before each fire, please implement it in my post processor, thank ...
by pdevloo
Sun Feb 02, 2020 8:09 pm
Forum: Problems and questions
Topic: How to increase pierce time before the torch starts moving
Replies: 1
Views: 731

How to increase pierce time before the torch starts moving

The torch only triggers when it begins to move which is a problem when utilizing tabs, what can I do to increase pierce delay time?
by pdevloo
Tue Jan 28, 2020 5:02 am
Forum: Chat
Topic: Mac Version
Replies: 2
Views: 712

Mac Version

I've gone through many discussions in the past about this on the forum but is there a Mac version?
by pdevloo
Sun Dec 29, 2019 12:31 am
Forum: Problems and questions
Topic: Sheetcam and Openbuilds Control
Replies: 15
Views: 2367

Re: Sheetcam and Openbuilds Control

"You have the rule set 'EOCAnti-Dive' set to be always applied. Go to Tools->Cutting rules. Set 'Always apply tool set' to 'None'" found this in another post and it solved my problem
by pdevloo
Fri Dec 27, 2019 8:11 pm
Forum: Problems and questions
Topic: Sheetcam and Openbuilds Control
Replies: 15
Views: 2367

Re: Sheetcam and Openbuilds Control

M67 E0 Q10 (DTHC OFF) This is causing me a warning, if erased from the G-Code rest runs perfect, how to eliminate?
by pdevloo
Sun Dec 22, 2019 5:38 am
Forum: Problems and questions
Topic: Sheetcam and Openbuilds Control
Replies: 15
Views: 2367

Re: Sheetcam and Openbuilds Control

Do you have a post processor available for plasma and Open Builds Black Box, if you do, found a lot of interest for it on the Openbuilds forum, router posts are there, nothing for plasma
by pdevloo
Sat Dec 21, 2019 4:15 pm
Forum: Problems and questions
Topic: Sheetcam and Openbuilds Control
Replies: 15
Views: 2367

Re: Sheetcam and Openbuilds Control

Forgot to mention, this is a plasma
by pdevloo
Fri Dec 20, 2019 8:50 pm
Forum: Problems and questions
Topic: Sheetcam and Openbuilds Control
Replies: 15
Views: 2367

Sheetcam and Openbuilds Control

Hi, I have been using SheetCam with a CandCNC system, really like the capabilities of sheetcam, so much so, that I want to use it with my new machine using Openbuilds Black Box and Control software, cant seem to get a Post Processor that works without fail. I'm using Solid Edge 2D for cad, only have...