Hi Rob,
It may be worth to mention, when we look from top view of the contour it looks perfectly fine. Puncture mark is getting created only on bottom side of the sheet.
Search found 9 matches
- Fri Aug 30, 2019 10:27 am
- Forum: Problems and questions
- Topic: Leaving small pit/puncture on back side of the sheet
- Replies: 6
- Views: 843
- Fri Aug 30, 2019 10:24 am
- Forum: Problems and questions
- Topic: Leaving small pit/puncture on back side of the sheet
- Replies: 6
- Views: 843
Re: Leaving small pit/puncture on back side of the sheet
Hi Rob,
Sorry forgot to mention, it is plasma cutting. I am not sure if it is kerf crossing however I am getting the same result when I tried with no lead out. I assume kerf crossing would happen when lead out is crossing lead in contour. Correct me if I am wrong.
and I am using Fangling controller.
Sorry forgot to mention, it is plasma cutting. I am not sure if it is kerf crossing however I am getting the same result when I tried with no lead out. I assume kerf crossing would happen when lead out is crossing lead in contour. Correct me if I am wrong.
and I am using Fangling controller.
- Fri Aug 30, 2019 6:51 am
- Forum: Problems and questions
- Topic: Leaving small pit/puncture on back side of the sheet
- Replies: 6
- Views: 843
Leaving small pit/puncture on back side of the sheet
Hi All, I am cutting a design on 2 mm MS sheet and getting small pit/puncture on back side of the sheet. Please find attached the picture. This seems to be problem with lead out as I verified by pausing the cut after lean in and there was no puncture. Have tried different types of lead in/lead outs ...
- Fri Aug 30, 2019 6:03 am
- Forum: Problems and questions
- Topic: Not getting THC ON/OFF option in path rules
- Replies: 11
- Views: 2661
Re: Not getting THC ON/OFF option in path rules
Thanks Les and Keith for your reply.
I have tried without semicolon as well. But no luck. As Les mentioned, it looks like those M codes are not recognized by Fangling controller.
I have tried without semicolon as well. But no luck. As Les mentioned, it looks like those M codes are not recognized by Fangling controller.
- Mon Aug 19, 2019 5:21 am
- Forum: Problems and questions
- Topic: Not getting THC ON/OFF option in path rules
- Replies: 11
- Views: 2661
Re: Not getting THC ON/OFF option in path rules
Hi Keith,
Good Morning..
Arcing check time is currently set in the controller as 15 seconds. I am getting "Arc Error" while loading the G code to controller from USB drive, not during cutting. If I am not setting path rules, it is working fine.
Good Morning..
Arcing check time is currently set in the controller as 15 seconds. I am getting "Arc Error" while loading the G code to controller from USB drive, not during cutting. If I am not setting path rules, it is working fine.
- Sat Aug 17, 2019 7:33 am
- Forum: Problems and questions
- Topic: Not getting THC ON/OFF option in path rules
- Replies: 11
- Views: 2661
Re: Not getting THC ON/OFF option in path rules
Hi Rob,
Yes, that's the post processor I am using. I had gone through the user manual however no where I find anything about the error that I am getting.
Yes, that's the post processor I am using. I had gone through the user manual however no where I find anything about the error that I am getting.
- Sat Aug 17, 2019 5:24 am
- Forum: Problems and questions
- Topic: Not getting THC ON/OFF option in path rules
- Replies: 11
- Views: 2661
Re: Not getting THC ON/OFF option in path rules
Thanks Rob and Les,
Please find attached my G code..
Please find attached my G code..
- Fri Aug 16, 2019 11:06 am
- Forum: Problems and questions
- Topic: Not getting THC ON/OFF option in path rules
- Replies: 11
- Views: 2661
Re: Not getting THC ON/OFF option in path rules
Hi Rob, Thank you for your reply. I have followed the video and added the code snippets for THC ON OFF. Then I set following rules 1. On circles smaller than 30 mm set feed to 60% and output code: THC OFF then output code THC ON after the circle. 2. On all corners tighter than 45 degrees set feed to...
- Wed Aug 14, 2019 9:49 am
- Forum: Problems and questions
- Topic: Not getting THC ON/OFF option in path rules
- Replies: 11
- Views: 2661
Not getting THC ON/OFF option in path rules
Hi All, I am new to sheetCam and new to this forum. I am currently learning various SheetCam features through you tube videos and came across Path Rules feature. I could see in the videos while defining the path rules, THC ON/OFF option however in my version of SheetCam, it is absent. Could some one...