Search found 23 matches
- Tue Apr 25, 2017 6:44 pm
- Forum: New features
- Topic: remnant nesting?
- Replies: 5
- Views: 5249
Have you thought about making your drawing size the same as your material size, then saving it as a template. Then you draw up your cuts on the sheet, saving the drawing each time as a template. So each time you have a project, you can draw it up and move it around the template until you can find a...
- Tue Apr 25, 2017 1:58 pm
- Forum: New features
- Topic: remnant nesting?
- Replies: 5
- Views: 5249
- Sat Apr 22, 2017 10:59 am
- Forum: New features
- Topic: remnant nesting?
- Replies: 5
- Views: 5249
remnant nesting?
Is this a future possibility or too much trouble?
Select points on a piece of scrap (remnant) on the table and import as a material size in sheetcam.
I used it a lot at my last job. would be very useful
Select points on a piece of scrap (remnant) on the table and import as a material size in sheetcam.
I used it a lot at my last job. would be very useful
- Thu Jan 12, 2017 3:01 pm
- Forum: Problems and questions
- Topic: another issue
- Replies: 6
- Views: 1801
- Thu Jan 12, 2017 2:38 pm
- Forum: Problems and questions
- Topic: another issue
- Replies: 6
- Views: 1801
- Thu Jan 12, 2017 2:38 pm
- Forum: Problems and questions
- Topic: another issue
- Replies: 6
- Views: 1801
- Thu Jan 12, 2017 2:19 am
- Forum: Problems and questions
- Topic: another issue
- Replies: 6
- Views: 1801
- Wed Jan 11, 2017 10:36 pm
- Forum: Problems and questions
- Topic: another issue
- Replies: 6
- Views: 1801
another issue
I had to install sheetcam on a new computer. I used the post processor per Luke at CandCNC. torch comes down, touches the ohmic sensor, goes up .150 then goes another .250" roughly, then pierces, lowers some (but not to the specified cut height) and cuts. on holes it never lowers to the cut hei...
- Fri Aug 05, 2016 6:45 pm
- Forum: Problems and questions
- Topic: G code issue
- Replies: 6
- Views: 2354
- Thu Aug 04, 2016 7:42 pm
- Forum: Problems and questions
- Topic: G code issue
- Replies: 6
- Views: 2354
- Thu Aug 04, 2016 6:53 pm
- Forum: Problems and questions
- Topic: G code issue
- Replies: 6
- Views: 2354
- Thu Aug 04, 2016 6:06 pm
- Forum: Problems and questions
- Topic: G code issue
- Replies: 6
- Views: 2354
- Thu Aug 04, 2016 4:09 pm
- Forum: Problems and questions
- Topic: G code issue
- Replies: 6
- Views: 2354
G code issue
I don't know if I changed a setting or what? when I run a new code on my plasma table (mach) the torch touches off, pierces and goes to the .060 cut height. but it stays locked there no matter the volts. If I run an older code it runs fine though.
Is there a setting somewhere?
Is there a setting somewhere?
- Tue Feb 03, 2015 2:17 am
- Forum: Yahoo posts
- Topic: Rotation of Part
- Replies: 1
- Views: 2118
Rotation of Part
Use the right and left arrow keys. Just above the space bar to the right Sent from my iPhone On Feb 2, 2015, at 8:00 PM, "jojomeyers11@yahoo.com ( jojomeyers11@yahoo.com ) [sheetcam]" <sheetcam@yahoogroups.com ( sheetcam@yahoogroups.com )> wrote: Hello Our shop uses oxy-fuel to cut metal p...
- Tue Sep 16, 2014 11:27 pm
- Forum: Problems and questions
- Topic: array feature
- Replies: 2
- Views: 1395