cant get the text to show up in sheetcam

agrifabs · Post by **agrifabs** » Wed Jan 21, 2015 4:58 pm

hi all, done a very basic pattern in autocad, i have imported in into sheetcam but the text doesnt show up, i have tried exploding the parts like someone advised me too, still nothing, the part is just some contact details i want to weld to my equipment that i manufacture, nothing special,

i have attached the file if any of you would like to have a go and explan where im going wrong?

another question - is there anyone on here from wales?
thanks in advance

chris

art · Post by **art** » Wed Jan 21, 2015 5:15 pm

Chris,
Can't explain why your having a problem.
I downloaded the drawing and opened it up to see if I could see any drastic
problems and found nothing wrong.
I then imported the drawing into Sheetcam Development 6.1.13 and the text
was there
I then tried to do a simulation of cutting and it worked fine?

By any chance, have you somehow turned the layer off in sheetcam????

Art
Country Bubba

At 11:58 AM 1/21/2015, you wrote:

hi all, done a very basic pattern in autocad, i have imported in into
sheetcam but the text doesnt show up, i have tried exploding the parts
like someone advised me too, still nothing, the part is just some contact
details i want to weld to my equipment that i manufacture, nothing special,

i have attached the file if any of you would like to have a go and explan
where im going wrong?

another question - is there anyone on here from wales?
thanks in advance

chris

agrifabs · Post by **agrifabs** » Wed Jan 21, 2015 5:25 pm

hi, thanks for the rapid response! just managed to get the text to show up in sheetcam (dont ask me how i done that!!) have run the post processor and opened it up it mach3 but only a few lines of gcode show up,

i have copied and pasted the gcode below

N0010 (Filename: agricbdxf.tap)
N0020 (Post processor: Mach3 plasma.scpost)
N0030 (Date: 21/01/2015)
N0040 G21 (Units: Metric)
N0050 G53 G90 G91.1 G40
N0060 F1
N0070 S500
N0080 (Part: agricbdxf)
N0090 M05 M30

any ideas why im not getting all the gcode from this file? ive really got to get to grips with all this software soon! think im going to go nuts otherwise!!

regards

chris

art · Post by **art** » Wed Jan 21, 2015 5:29 pm

From the looks of the gcode, it only did the "setup" part and none of the
operations.
Are you sure you made the operations before hitting post????

Best guess on my part.

Art
Country Bubba

At 12:25 PM 1/21/2015, you wrote:

hi, thanks for the rapid response! just managed to get the text to show up
in sheetcam (dont ask me how i done that!!) have run the post processor
and opened it up it mach3 but only a few lines of gcode show up,

i have copied and pasted the gcode below

N0010 (Filename: agricbdxf.tap)
N0020 (Post processor: Mach3 plasma.scpost)
N0030 (Date: 21/01/2015)
N0040 G21 (Units: Metric)
N0050 G53 G90 G91.1 G40
N0060 F1
N0070 S500
N0080 (Part: agricbdxf)
N0090 M05 M30

any ideas why im not getting all the gcode from this file? ive really got
to get to grips with all this software soon! think im going to go nuts
otherwise!!

regards

chris

agrifabs · Post by **agrifabs** » Wed Jan 21, 2015 5:40 pm

yes ive done everything the sheetcam tutorial has said to do! ive included a screenshot of my sheetcam just before i press the post processor button!

Post by **Les Newell** » Wed Jan 21, 2015 5:45 pm

That all looks correct. As Art suggested, have you tried running simulation (mode->simulation)?

If the simulation runs correctly you should get correct g-code.

agrifabs · Post by **agrifabs** » Wed Jan 21, 2015 5:49 pm

thanks les! didnt even know that existed! when i press start on the simulation a window comes up that says - warning- feedrate is zero?? where do i alter that?

Post by **Les Newell** » Wed Jan 21, 2015 5:52 pm

Double click on your operation (where it says No offset, Default...) to open it.
You can set the feed rate in there.

By the way in simulation click the setup button and set the machine type to 'jet' rather than 'mill'

agrifabs · Post by **agrifabs** » Wed Jan 21, 2015 5:56 pm

its set at 6000mm/min, set it to jet instead of mill and still the same!

Post by **Les Newell** » Wed Jan 21, 2015 5:59 pm

Edit your tool and check the plunge rate. You will get that error if the plunge rate is 0.

agrifabs · Post by **agrifabs** » Wed Jan 21, 2015 6:05 pm

plunge rate set at 300mm/min

included a screeshot of the settings etc

Post by **Les Newell** » Wed Jan 21, 2015 6:07 pm

Could you post the job file so I can try it here.

agrifabs · Post by **agrifabs** » Wed Jan 21, 2015 6:09 pm

yes no problem mate

Post by **Les Newell** » Wed Jan 21, 2015 6:23 pm

I just tried your job here and it worked. I have a suspicion you may have a corrupted license. Do you have a license? Go to Help->about. Does it say if SheetCam is licensed?

agrifabs · Post by **agrifabs** » Wed Jan 21, 2015 6:33 pm

just messaged you les, its says its licsened