Search found 3663 matches
- Mon Mar 11, 2024 5:10 pm
- Forum: Problems and questions
- Topic: Mach4-swiftcut post processor
- Replies: 14
- Views: 2735
Re: Mach4-swiftcut post processor
Sorry, I should have looked at the thread title. Looking at the post, you should have a 'Tool type' option in your tool definition. That controls the tool number.
- Mon Mar 11, 2024 2:59 pm
- Forum: Problems and questions
- Topic: Mach4-swiftcut post processor
- Replies: 14
- Views: 2735
Re: Mach4-swiftcut post processor
What post processor are you using?
- Fri Mar 08, 2024 3:55 pm
- Forum: Problems and questions
- Topic: Z action being added, this is new
- Replies: 1
- Views: 891
Re: Z action being added, this is new
Have you updated your post processor recently? If not it may be worth installing the latest post from CandCNC.
- Mon Mar 04, 2024 3:46 pm
- Forum: New features
- Topic: Turning module
- Replies: 81
- Views: 225741
Re: Turning module
Sorry for the late reply. I just realized what is wrong. In the passes tab of your cut operation it is worth setting up a lead in and lead out. A good starting point for both lead in and lead out is an arc radius of 1mm (0.04") and a line length at least equal to your cut depth. Set the angle t...
- Thu Feb 29, 2024 1:20 pm
- Forum: Problems and questions
- Topic: Bug and Requests
- Replies: 9
- Views: 10273
Re: Bug and Requests
The reason why I have been holding off is that proper tip-up avoidance is hard. What I did is a hack that only works in some situations. It just happens to work well for your specific application.
I don't know what is going on with the profiles. I'll continue testing and see what I can find.
I don't know what is going on with the profiles. I'll continue testing and see what I can find.
- Wed Feb 28, 2024 6:04 pm
- Forum: Problems and questions
- Topic: Bug and Requests
- Replies: 9
- Views: 10273
Re: Bug and Requests
I tried it just now and it worked. Could you try again.Link says file not found....
- Wed Feb 28, 2024 3:55 pm
- Forum: Problems and questions
- Topic: Bug and Requests
- Replies: 9
- Views: 10273
Re: Bug and Requests
Hey Les, hope all has been well! We've been crazy busy over here and I haven't had time to bother you with requests and bug fixes. I'm sure you have enjoyed my silence lol. I was beginning to think it was something I said :lol: Did you ever get a chance to look into this? It looks like the profiles...
- Wed Feb 28, 2024 12:41 pm
- Forum: Problems and questions
- Topic: First correct answer wins....
- Replies: 1
- Views: 886
Re: First correct answer wins....
Sorry for the delay in answering but you should not need any extra software. In SheetCam go to Options->machine->post processor and select the burny25 post processor. Next change the 'Output file extension' setting to nc instead of tap.
- Wed Feb 28, 2024 12:37 pm
- Forum: Problems and questions
- Topic: Maybe a Bug: Can't update operation new code snippet
- Replies: 4
- Views: 956
Re: Maybe a Bug: Can't update operation new code snippet
Could you send me an example job file demonstrating the issue.
- Wed Feb 28, 2024 12:35 pm
- Forum: Problems and questions
- Topic: Can run test but machine doesn't penatrate
- Replies: 3
- Views: 2639
Re: Can run test but machine doesn't penatrate
I'm sorry but I have never used a Burny controller, so I don't know. Hopefully the Burny manual should tell you.
- Fri Feb 23, 2024 11:04 am
- Forum: New features
- Topic: Turning module
- Replies: 81
- Views: 225741
Re: Turning module
It looks like the taper from the tool post angle is caused by the path generator appying the tool path angle the wrong way around. Reversing the turrent angle generates the correct tool paths but simulation will get upset. I'll have to fix this. The outer diameter and inner diameter are roughly the ...
- Thu Feb 22, 2024 4:32 pm
- Forum: New features
- Topic: Turning module
- Replies: 81
- Views: 225741
Re: Turning module
It's starting the path 1 tool radius in from the start point and ending 1 tool radius before the end point.
Looking at the code I specifically offset the start and end points but now I have no idea why I did it!
Looking at the code I specifically offset the start and end points but now I have no idea why I did it!
- Thu Feb 22, 2024 1:38 pm
- Forum: New features
- Topic: Turning module
- Replies: 81
- Views: 225741
Re: Turning module
Sorry for the delay in replying. I just emailed you a temporary license. The generated code should be in diameter mode. The slope had me puzzled for a moment but it is caused by your tool definition. You have a side angle of 0 degrees with a clearance angle of 2 degrees. When generating tool paths S...
- Tue Feb 20, 2024 12:05 pm
- Forum: Problems and questions
- Topic: Application Colors
- Replies: 6
- Views: 54203
Re: Application Colors
Is this with AMD on-board graphics or with an AMD card? The issue must be only on specific AMD setups or I would have more complaints of this issue.
Try enabling View->Show true width. Does that help?
Try enabling View->Show true width. Does that help?
- Fri Feb 16, 2024 12:14 pm
- Forum: Problems and questions
- Topic: Toolbar direct button links to diffrent postprozessors setups who ?
- Replies: 2
- Views: 989
Re: Toolbar direct button links to diffrent postprozessors setups who ?
Just to add to djreiswig's suggestion you can find the plugin in Options->plugin options->moreposts.